Panamax MX5102 Home Theater Power Management with Battery Backup

Model: MX5102 UPC: 050616008501 Item: 153023


In Stock
Shipping Information
Show Store Details
104 E Vine St. Hatfield, PA 19440
  • Mon - Fri: 9am - 4pm
  • Sat: By appointment only
  • Sun: Closed
(866) 961-7781
Show Store Details
754 Route 309 (Bethlehem Pike) Montgomeryville, PA 18936
  • Mon: 9:30am - 8pm
  • Tues - Fri: 9:30am - 6pm
  • Sat: 9:30am - 5pm
  • Sun: 12pm - 5pm
(215) 368-8343
Show Store Details
38 Greenfield Avenue, Ardmore, PA 19003
  • Mon - Fri: 10am - 6pm
  • Sat: 10am - 5pm
  • Sun: Closed
(610) 649-7002
Choose a Store Location

More Product Details

Questions? We're here to help.

Product Information

Combining Power Management with Battery Backup for a Smart Solution

Panamax's MX5102 Home Theater Power Management with Battery Backup is specially designed and engineered for home theater systems. In addition to power management, the battery backup prevents processor-controlled devices and hard-drive based sources from losing critical data and setup configurations, as well as allowing for a proper shut-down procedure.

Battery Backup

MX5102 prevents critical equipment from losing setup configuration, stored data, and hard-disk information. Shuts off projection equipment via IR control to allow the projector bulbs to go through a proper cool-down cycle before shutting off.

Improves Picture and Sound Quality

Power cleaning and linear filtration eliminate common symptoms of contaminated power (including loss of detail, pops, hisses, hums, and visual artifacts), and allow your A/V equipment to perform up to its full capability.

Reduces Cross-Contamination Between Components

The MX5102 is designed to provide noise isolation between four isolated outlet banks including two battery backup outlets, so that any noise created by an A/V component cannot contaminate the power going to equipment plugged into another outlet bank.

Monitors Incoming Line Voltage and Provides Visual Indication of Power Level

Panamax's patent pending AVM circuitry continuously monitors the incoming power as displayed on the digital volt meter. In case of an undervoltage or an overvoltage, a flashing red LED will be displayed on the front panel, and power to the connected equipment is automatically turned off for all outlets except for the battery connected ones, if either of these conditions is detected. When voltage returns to a safe level, power to the equipment is automatically reconnected.




  • Line voltage: 120V
  • Number of outlets: 10
  • Number of isolated power banks: 4
  • Rack mountable: Yes
  • Rack ears included: Yes
  • Front panel meter(s): LED display indicates incoming line voltage or estimated minutes of backup time
  • Front media light(s): No
  • Control: On/off control to all outlets through front panel power button or low voltage trigger
  • Compliance: cCSAus
  • Low voltage trigger: 3 - 18V DC in
  • AC power cord: 10 ft., captive
  • Dimensions (W x D x H): 17" x 13" x 4"
  • Weight: 27 lbs.

Battery Backup

  • Output frequency: 60Hz ± 1%
  • UPS output capacity: 600VA, 360W @ 0.6pf
  • Regulation output range: 120 ± 5% simulated sine wave
  • UPS backup time (full load): 3 minutes
  • Transfer time: < 10ms

AC Protection

  • AC protection technology: 
    • Protect or disconnect
    • Automatic Voltage Monitoring
  • Automatic Voltage Shutoff: Yes
  • Undervoltage shutoff: 90V ± 5V
  • Overvoltage shutoff: 150V ± 5V
  • Maximum current rating: 12 (Amps)


  • Filtration technology: RFI/EMI filtration
  • Filtration rating 
    • All outlets
      • -30dB min. @ 100kHz
      • -50db max @ 270kHz

Signal Line Protection

  • Signal line protection: 1 LAN, 1 tel, 3 cable/satellite

Other Specifications

  • LAN protection - wires protected: 8 wires
  • LAN protection - jacks: RJ-45
  • LAN protection - compatibility: 10/100bT
  • LAN protection - clamping level: 50V
  • Telco protection - wires protected: 2 wires, 1 pair (4, 5)
  • Telco protection - fuseless/auto-resetting: Yes
  • Telco protection - clamping level: 270V
  • Telco - suppression modes: Metallic and longitudinal
  • Coax protection - shielded: Yes
  • Coax protection - insertion loss: < 0.5dB
  • Coax protection - HD 1080 i/p ready: Yes
  • Coax protection - frequency range: 0MHz - 2.2GHz
  • Coax protection - connections: Female "F", gold-plated
  • Coax protection - clamping level: 75V
  • Coax protection - bidirectional: Yes


What's in the Box

What's in the Box:

  • MX5102 Home Theater Power Management with Battery Backup


Customer Reviews for Panamax MX5102 Home Theater Power Management with Battery Backup

There are no reviews for this item. Write Review


Customer Q & A

Have a functionality, compatibility, or otherwise product-specific question about this product? Ask it here! If you have a customer service or shipping question, please direct it to our customer service department

Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!